FAC0420-02
3-Channel 4–20 mA Current Sensor
The 3-Channel 4–20 mA Current Sensor from Fidar Electronics reads the standard 4–20 mA output of any industrial transmitter and maps it back to engineering units. It connects to a FIDAQUIRE data logger over a daisy-chained CANopen bus.
Standard 4–20 mA input
Three independent input channels in one unit
Works with any industrial 4–20 mA transmitter
Broken-wire detection below 4 mA
RJ45 output on a CANopen bus
Daisy-chains up to 64 sensors per card
Works with the FBC0232-01 card and FIDAQUIRE logger
Up to 500 m of bus at 125 kbit/s
The 3-channel 4–20 mA sensor is an industrial analog input module designed to receive and monitor signals from three independent industrial transmitters simultaneously. It allows three measurement devices with standard 4–20 mA current outputs to be connected to the FIDAQUIRE monitoring system.
The module supports various industrial transmitters, including pressure, level, flow, temperature, humidity, and pH transmitters. The conversion of current signals into physical measurement units, such as bar, meters, or degrees Celsius, is configured in the monitoring software.
One of the key advantages of the 4–20 mA standard is its live-zero principle, where 4 mA represents the zero measurement value. Therefore, a current below the specified 4 mA threshold can indicate a broken wire or transmitter fault. This allows the system to identify signal faults separately instead of incorrectly recording them as zero measurements.
Key features of the 3-Channel 4–20 mA Sensor
Three independent input channels for industrial transmitters
Independent broken-wire and signal fault detection on each of the three input channels when the current drops below 4 mA.
Standard 4–20 mA current signal input
Compatible with industrial transmitters featuring 4–20 mA outputs
Broken-wire and input signal fault detection below 4 mA
RJ45 interface for CANopen bus communication
Daisy-chain connection of up to 64 sensors per card
Compatible with the FBC0232-01 card and FIDAQUIRE data logger
Communication distance of up to 500 meters at a transmission rate of 125 kbps
Communication and Connectivity
The 3-channel 4–20 mA sensor connects to the CANopen communication bus through its RJ45 interface and transmits measurement data to the FIDAQUIRE monitoring system at a communication rate of 125 kbps.
With three independent input channels, the module can acquire signals from three separate industrial transmitters. Furthermore, the ability to connect up to 64 sensors in a daisy-chain configuration on the FBC0232-01 card allows the monitoring system to be expanded to cover multiple measurement points.
The module also supports input signal fault detection and fault reporting through the data logger.
Each of the three input channels independently detects signal faults, and the fault status of each channel is reported separately through the data logger.
Where it is used
Reading pressure, level, flow and temperature transmitters
Tank and pipeline monitoring in oil, gas and petrochemicals
Bringing environmental analysers into a monitoring system
Pumping stations and water/wastewater treatment plants
Retrofitting legacy instruments into a modern monitoring stack
Air-quality and emission-measurement systems
Installation
To ensure reliable communication and minimize electromagnetic interference, shielded twisted-pair cables are recommended for the communication path.
The cable shield should be grounded at only one end to prevent ground loops. Proper cable routing and equipment connections also help improve communication stability and ensure reliable system operation.
| Dimensions | Height 3 cm, Depth 12 cm, Width 10.5 cm |
|---|---|
| Weight | 0.3 kg |
| Operating temperature | -10 to 45 °C |
| Storage temperature | -20 to 60 °C |
| Operating humidity | 0 to 60%, non-condensing |
| Warranty | 2 years |
| Mount | 2 Wall-mount holes |
| Input | 4 to 20mA Current |
| Number of Inputs | 3 inputs |
| Output | RJ45 CANopen bus |
Typical applications: • Reading pressure, level, flow and temperature transmitters • Tank and pipeline monitoring in oil, gas and petrochemicals • Bringing environmental analysers into a monitoring system • Pumping stations and water/wastewater treatment plants • Retrofitting legacy instruments into a modern monitoring stack • Air-quality and emission-measurement systems
FAC0420-02-Usermanual-EN
v1.0 · EN · 963 KB




